To stave off the cold, I’ve created a Viking six panel hat
created out of a deep burgundy garment sheepskin with rabbit fur trim. It’s lined with matching burgundy linen for
extra warmth. The basic six panel hat and
lining are pretty easy to make; the fur trim took up the most time and effort.
Materials used include: Garment sheepskin, linen, rabbit
fur, and thread to match the sheepskin. While
I went with natural materials, you could easily substitute other fabrics or faux
fur if you wanted.
Additional materials include: Sewing machine with leather
needle, scissors, measuring tape, sharp knife, marker, needles, thread to match
the fur, small clips, white charcoal pencil, ruler, pencil, pen, ruler, and straight
pins.
First, I created a pattern for the six panels that will be
connected to make the hat. For scale, every
four squares is equal to one inch. The
hat ended up with a circumference of 22 inches, so you may want to adjust the
pattern or the seam allowance depending on your desired circumference.
I traced the pattern onto the linen six times with the charcoal
pencil and then cut out the panels.
I repeated the process with the sheepskin, marking the ‘leather’
side with a marker since I want the suede side to show on the finished product.
Next, I stitched one edge of the lambskin panels together as
shown, with the suede sides touching in the middle. I used clips since pinning leather isn’t
desirable.
This shows the seam allowance I used. Next I attached the other end to the next
panel and repeated until all six panels were stitched together.
I followed the same steps for the linen, except I was able
to use pins instead of clips. If you are
unsure about the sizing of the hat, you may want to do the linen section before
the sheepskin one. Linen is much more
forgiving to fix (and cheaper to scrap if you need to start over.)
After the six panels were stitched together, I folded the
seams over and stitched them down. This
will help strengthen the hat and allow it to lay nicely.
I wasn’t able to stitch all the way to the center of the hat
using the sewing machine, so I flipped the hat to the suede side and finished stitching by hand.
I measured and cut a strip of linen approximately 3.75
inches by 24 inches (circumference of the hat plus an extra inch on each end)
to use for the backing of the fur trim. You
could also sew the fur directly onto the hat instead, but the rabbit skin is
delicate and I wanted a little additional strength and reinforcement.
I cut two matching strips of rabbit fur. They were just barely long enough for my hat so
you will want to measure and select your fur accordingly. It’s also important to make sure that the
color and direction of the fur on the pieces that you use matches. Alternatively, you could use another type of
animal with a larger pelt to avoid using multiple pieces. I used a sharp knife to cut the rabbit skin-
you don’t want to use scissors because you will cut the fur, too. You just want to very carefully cut the layer
of skin apart.
To attach the two strips of fur, I placed them so the fur
sides were touching and stitched the ends together. Then I stitched the fur to the linen strip by
hand (back of strip shown to demonstrate position of stitching.) I used thread that was similar in color to
the rabbit fur for any stitching that would actually go through the rabbit
skin.
At this point, there were three pieces to the hat- the outer
suede part of the hat, the linen lining, and the fur trim attached to a strip of linen.
The lining should be turned so that it fits inside the suede
hat so that the seams aren’t showing.
The linen strip has one edge that overlaps with the fur and one end that is
just linen. I fit the end that is just
linen between the suede hat and the linen lining (fur side down) and stitched
it as shown.
This way, the machine stitching attaches all three pieces
but doesn’t actually go through the rabbit fur itself.
Lastly, I turned up the fur trim to the desired length and
hand stitched the fur to the suede hat.
(Just a few small stitches per panel held it in place.) The back of the hat where the two ends of the
rabbit fur met required more stitching.
This is the finished hat.
